- Read and download GoPro Camcorder HERO + LCD Operating Instructions online. Download free GoPro user manuals, owners manuals, instructions, warranties and installation guides, etc.
- To download this user manual in a different language, visit. HERO Port 10. Battery Door 11. Wireless On/Off Button 12. Audio Alert 13. Microphone / The Basics.Playback appears only if the camera is connected to a TV or LCD Touch BacPac (optional accessory, sold separately). / Camera Status Screen MODES CAMERA SETTINGS.
Introduction
![Hero Lcd Manual Hero Lcd Manual](/uploads/1/2/5/0/125073370/317217373.jpeg)
Is your LCD cracked or not working properly? Use this guide to help replace it, and return your GoPro to tip top shape!
- iFixit Opening Tools
- Spudger
- Heat Gun
- Phillips #00 Screwdriver
GoPro Hero 7 Black Manual. Download: GoPro Hero 7 Black Manual. About the GoPro Hero 7 Black. The GoPro Hero 7 Black from GoPro Inc. Is a compact digital camera used for action sports & travel photography released in 2018.
- GoPro Hero3 Plus Black Front Panel
- GoPro Hero3 Plus Black Image Sensor
- GoPro Hero3 Plus Black Rear Case
- GoPro Hero3 Plus Black Expansion Port
- GoPro Hero3 Plus Black Motherboard
- Pull the tab on the back of the device to release the back cover. It should come right off.
- The device pictured does not include the back cover.
- Use the battery tab to pull the battery out of the device.
- Remove the battery from the slot.
- Using a plastic opening tool, pry the gray, front face plate until it can be removed from the housing.
- To avoid breaking or weakening the tabs on the face plate which hold it in place, alternate the sides from which you pry and check each tab before separating the plate from the body.
- Using your screwdriver, remove the four 8.1mm PH00 screws securing the motherboard to the black housing unit and set them aside.
- Use the plastic opening tool to help pry the motherboard/midframe up from the main housing. Once you can get a hold of the edge, simply pull the internal components up and out!
- Watch out for the ribbon cable connecting the midframe and the motherboard to the GoPro housing. See the next step.
- Remove the ribbon cable connecting the housing to the motherboard by flicking up the black clip with the spudger tool and gently pulling the cable out.
- Once the internal components are removed, take out your handy dandy spudger tool and pry off the piece of tape that holds down the image sensor.
- Disclaimer: Our device is just a teardown unit and no longer has the tape. The markup depicts the location where the tape would be located.
- Using your screwdriver, remove the four PH00 screws securing the image sensor to the motherboard.
- Windows xp product key generator. Disclaimer: The unit used for this guide did not include these screws. Set them aside so you do not mix them up with the previously removed screws.
- Using the spudger tool, pry off the connector ribbon from the motherboard (don't worry it comes off pretty easily).
- Remove the image sensor from the motherboard assembly. Ganpati songs free download.
- Using your screwdriver, remove the three 4mm PH00 screws that hold down the metal plate.
- Using the spudger tool, pry off the corresponding ribbon cable from the motherboard.The game is an amazingly original blend of chess, fantasy strategy, puzzle, and even a bit of action. Hard to describe- but must be played to be believe. Archon video game. Archon is a great classic I loved back then on the C64. Each side exists to conquer, by eliminating all of the opposing pieces or controlling the five power points.'
- The microSD/accessory board is ready to come off.
- Using your trusty screwdriver, remove the single 3.2mm PH00 screw connecting the motherboard to the midframe.
- Use the spudger tool to disconnect the front LCD from the motherboard. Gently pull the ribbon cable out.
- Gently pull the motherboard away from the midframe.
- Now that you have removed the plastic midframe from the motherboard, nothing is standing in the way of the LCD!
- Carefully remove the ribbon cable from the midframe. It is attached with glue, so a spudger tool (or a heat gun if it's stubborn) will be needed.
To reassemble your device, follow these instructions in reverse order.
To reassemble your device, follow these instructions in reverse order.
4 other people completed this guide.
Gopro Hero 3 Lcd Screen Manual
Embed this guide
Choose a size and copy the code below to embed this guide as a small widget on your site / forum.